Stress Concentration on a Plate with hole Geometries

For this challenge, simulate the bending of iPhone as per the given cases below Case 1: Simulate the model as it is given in the video Case 2: Move the bottom fingers from their defined position to the given position X= 22.5mm & Z= 10mm and obtain the results for the simulation. Also define the S-N curve…

                                  Title : Rotating Shaft With Unbalanced Mass What is Vibration motor? Vibration motors are totally enclosed 3 Phase motors with adjustable, eccentric weights mounted at both the ends of the shaft, to set…

Challenge : To perform explicit analysis in bullet penetrating bucket challenge For this analysis we have a 3D Geometry of Bullet and Bucket, this is how model lookslike.                 In this analysis 3 different materials will be used for bucket and for bullet only Tantalum will…

Challenge: We have simulate a frontal impact car crash. A car with a certain speed hits at front part with object to undergoes front impact. This can also be define exactly opposite by an similar object hitting the stationary car\'s front part. Here, same approach we have used by assigned an oblect to hit a stationary…

Challenge : Tension Test- Displace one end of the specimen by 18mm while keeping the other end fixed. Torsion Test - Displace one end of the specimen by 1200 degrees while keeping the other end fixed. Find out Equivalent Stress, Total Deformation and Temperature (User Defined Result) for both cases and compare the results.…

Challenge : To perform an explicit dynamics simulation to find out the Equivalent Stress, Total Deformation and also insert a User defined result to calculate the temperature of the body. You need to perform this for 2 cases. One will be with a cutting velocity of 20000mm/s and the other will be with a cutting velocity…

To perform transient structural analysis on a worm gear assembly. This model is imported in ANSYS SpaceClaim. Then In geometry, cutting the gear by half so to bring the model within Academic limits. Updating the model to work on the model for transient structural analysis.              …

To perform a transient structural analysis on a double universal joint with a spring usingthree different materials Structural Steel, Stainless Steel and Titanium alloy on the jointwith the spring. This model is imported in geometric in Ansys 15. Then this model opened in mechanical model. In geometry, no need to change…

The challenge has been setup to perform a transient analysis on a cam and cam-follower. The following model was imported from the internet and inspected for damages by opening it in space claim, then material was set to structural steel for Model.                      …

This challenge to simulate the rolling operation on a workpiece made of copper. The model is provided. Increase the length of the workpiece by 60mm and decrease its size on both sides by 8mm. Run the simulation for 14 steps and random values for the displacement. Ensuring that the edge of the workpiece is displaced by…

For this challenge, performing the analysis to simulate a sphere pressing on a plate. Pressing the sphere onto plate 4mm downwards and retract it. The model was imported from the internet since the model is symmetric 1/4th of themodel was taken into account solving the stresses and strain,later the effects could bemirrored…

Challenge : To run a simulation of bending a wire using a static structural system forthree different cases. The Wire Bending model first imported to ansys and then material was set to structural steel for Wheel & Lever and Copper Alloy NL ( Case 1 ), Aluminium Alloy NL ( Case 2 ), Magnesium Alloy NL ( Case 3 ) for…

Case 1 .  Stainless Steel: In this case, the material of the plates must also be the same. Use Stainless steel for both weldments and plates. No need to add flux to the weldments. The Weld Joint Model was first imported to ansys, checked if there is any problem in geometry while importing. after confirming model import…

The Railwheel,track model first imported to ansys and then material was set to structural steel for both Cases.                                 Connections Settings :  The contacts as detected by ansys were changed to rename by its definition…

1) Grid lndependency Test’ and ‘Mesh Refinement Test‘ are the synonyms and they all mean the same. While performing Finite Element Analysis, one of the most common question is finite element mesh quality. How can one know if the mesh is good enough for the analysis? Mesh density is used to control accuracy…

Case 1:                    Using Cast Iron (ductile) as a material from Ansys Library after selecting Material, I Imported the Geometry in Ansys, then while meshing I took by default value, then for finer mesh I use value 1 mm.   Stress Intensity : when fracture occurs, …

Case 1 Plate dimensions: Length=300mmHeight=120mmThickness=30mmCircular Hole at the center:Diameter=60mm Boundary Conditions:Plate fixed at left face.Load of 500N on the right face.   Material : For Case 1               Note : All settings in Both Cases were same.   Case 1 :…