MESHING BMW M6 AND CREATING A WIND TUNNEL USING ANSA

OBJECTIVE: To simulate the side crash analysis of the given neon model. STEPS: UNIT SYSTEM: During whole analysis, Kg KN mm ms was followed. INTERFACES: Deleted already defined interfaces and created Type 7 global interface. The properties for the Type 7 interface are: Istf=4 Igap=3 Idel=2 Fscale= 0.8 Inacti = 6 Iform…

OBJECTIVE: To perform a frontal crash simulation using Radioss as a solver. STEPS: View components: In the NEON FRONT model there are 75 components. ASSIGNING MATERIAL ID, PROPERTY ID, AND CARD IMAGE: For rigid bodies, card image is none and prop id, mat id is unspecified. CONTACTS: Under groups, contact cards are defined.…

OBJECTIVE: Studying Interfaces and boundary condition in Hypercrash, Hypermesh and meshing bumper assembly MESHING OF BUMPER ASSEMBLY: Topological error like faces not connected was removed using extend option under surface edit option. Auto mesh under 2D option was used for meshing. Mesh size was  6mm with element…

OBJECTIVE: Through this challenge, we will study different material laws in Radioss and will select the best material law for the given scenario by simulating and plotting graph. STEPS CASE1: Changing the model name from FAILURE_JOHNSON_0000 to Law2_epsmax_failure.Running the model as it is, without changing shell properties…

OBJECTIVE:To compare the results with base simulation and improved shell elements properties by performing energy, mass error checks, plotting graph in HyperGraph and animating in HyperView. SIMULATION 1: With default Shell Properties. Imported Element_Formulation-Shell-3_assignment_0000.rad file. Property was not changed.…

OBJECTIVE: To compare the results with base simulation and improved shell elements properties by performing energy, mass error checks, plotting graph in HyperGraph and animating in HyperView. SIMULATION 1: With default Shell Properties. Imported Element_Formulation-Shell-3_assignment_0000.rad file. The property was…

OBJECTIVE: To clean the geometry, extract mid surface, mesh the extracted surface and assign thickness to given models. LINK TO HYPERMESH FILES https://drive.google.com/file/d/1Op9RLc8y85U2qtlLyBNh5GYCglVHuNqN/view   PROCEDURE: Model was imported and to see errors in model, geometry color mode was set to mixed. …

OBJECTIVE: Surface mesh and volume mesh generation on given housing and arm bracket model. LINK TO HYPER MESH RADIOSS FILES: https://drive.google.com/file/d/1h0tOn4b9e9EDoVFqaGuKCjnWRgrHxUvL/view 3D MESHING: 3D Elements should be used when all dimensions are comparable. x~y~z Element shape: Tetra, Penta, Hex, Pyramid Element…

OBJECTIVE: To find minimum pressure using Newton-Raphson method PROGRAMMING EXPLAINED: Two functions are defined. f and fprime. These function are defined to calculate next iteration value using NR method. To calculate pressure values for different thickness, for and while loop was used.In while loop absolute value of…

OBJECTIVE: To demonstate file parsing using Python. when we run the program, first thing appears is  to enter the filename,if we speicify correct name then we can see the rest output otherwise a message will show file not found. To store different properties like crank, pressure, density,etc empty array was created.…

OBJECTIVE: To curve fit given data using linear and cubic polynomial. For curve fitting, we imported curve_fit from scipy library. Defined two function, func and func1 which are used for fitting curve. Defined another function read_file to read temperature and cp values. Values were split using (,) and values were append…

OBJECTIVE: To curve fit given data using linear and cubic polynomial. For curve fitting, we imported curve_fit from scipy library. Defined two function, func and func1 which are used for fitting curve. Defined another function read_file to read temperature and cp values. Values were split using (,) and values were append…

OBJECTIVE: Solving differential equation using ODEINT and simulating motion of pendulum using solution from ODE. Given ODE of 2nd order.   PROGRAMMING EXPLAINED: 1.To solve ODE of 2nd order, we have to convert above equation into two, single order ODE. `(d(theta1))/(dt)=(theta2)`---->1 `(d(theta2))/(dt)+(b/m)*(theta2)+gsin(theta1)/(l)=0`------2…

OBJECTIVE: In this challenge, we will find minimum value of the given function which is constrained by other function. SOLUTION: Given: `f(x,y)=5-(x-2)^2-2(y-1)^2` constrained to `x+4y=3` Optimization: `g(x,y)=5-(x-2)^2 -2(y-1)^2+lamda(x+4y-3)` `(partialg)/(partialx)=0;` `implies -2(x-2)+lamda=0`----->(A) `(partialg)/(partialy)=0;`…

OBJECTIVE: In this challenge, we will plot pressure-volume reationship for otto cycle by varying crank angle from 0-180degree. PROGRAMMING EXPLAINED: Initially we are provided with p1,t1 and t3. Rest values at state points are calculated using combined gas law formula and below formula.          …

OBJECTIVE: In this challenge, we will calculate drag force experienced by cyclist and plot these values against velocity and drag coefficient. PROGRAMMMING EXPLAINED: Imported Matplotlib which is data visualization library for python. Defined INPUTS. For first plot coefficient of drag, frontal area and density of air are…

OBJECTIVE: To remove all topological error and perform hemming operation for a given hood panel. METHODOLOGY: Geometry clean up Isolating inner panel and extracting the midplane. Isolating inner panel and extracting the midplane Assigning PID and thickness to both midplanes. Isolating Hemming region and assigning PID and…

OBJECTIVE: Perform surface mesh and create Wind Tunnel for flow analysis over BMW M6. PROCEDURE: GEOMETRY CLEANUP: Styling lines were left in the model. These were deleted by making them visible using macros and deleted using DELETE option. In cars body, various errors were removed like extra faces and overlapping geometry.…

OBJECTIVE In this challenge, we tried to clean up the geometry and perform surface mesh and volume mesh for given mesh sizes for diferent PID. METHODOLOGY Removing all topological error. Renaming PID Combining volume Generating surface mesh. Generating volume mesh. PROCEDURE TOPOLOGICAL ERRORS As we open the model we can…

OBJECTIVE The main obejctive of this challenge is to mesh the given cylinder model in ANSA with a given mesh size of one units. METHODOLOGY Import the model. Set-up the display. Make geometry error free by using check option present in ANSA. Setting PID for different surfaces. Generating mesh. PROCEDURE First we imported…