Fender Design

Dear Support, I completed the Final Project of Development of Door Trim Panel design. Find the below screenshots and attached files of 3d and project report PPT for review. Thanks & Regards,Gowtham Kumar P.  

Hello Team, As per challenge, I have developed the B pillar part along with the plastic features as per the Master section. see the attached files and the below screenshots for review and give your feedback. Thanks & Regards,Gowtham Kumar P.    

Hello Support,I have completed the challenge by creating the attachment features 4 way locators, 2 way locator and Heat stakes to assemble the applique to Door. See the attached files and below screenshots for review. Thanks & Regards,Gowtham Kumar P.

Hello Support,Created the screw boss and the dog house as per the design rules. Please find the below screenshots and the attached files of cat part and PPT for review.Let me know the feedback.   Thanks & Regards,Gowtham Kumar P.

Switch Bezel Part Design: As per the challenge, i have created the closed body of Switch Bezel model along with Tooling direction and checked for the draft analaysis. See below PPt for the detailed steps followed. Thanks & Regards,Gowtham Kumar P.

Creation Door Arm rest catpart:As per the challenge created the Door Arm rest catpart with proper Tooling axis and performed draft analysis.Please find the below screenshots for quick review and the same attached along with Catpart. Please review and give your feedback. Thanks & Regards,Gowtham Kumar P.

Objective: Using the given styling surface of Back door develop the design of Back door Inner panel. Develop the necessary embosses to strengthen the inner panel. Check and validate the draft analysis of the developed design of Inner panel. Develop the design of outer panel with the necessary hemming definition and the…

Objective: For the Given Roof styling, develop the essential flanges and reinforcements. Creation of Roof ditch area with tool opening angle of 3 degree. Provide appropriate dimensions and validate for Draft analysis. Section modulus study on 0-Y section for the Master sections created for Front roof rail, Rear roof rail,…

Objective: Use the Section of Hood design and calculate the section modulus using the formula S = I/yS = Section ModulusI = Moment of InertiaY = distance between the neutral axis and the extreme end of the object  Create a new section that has improved the section modulus of the previous section Consider Stainless…

Objective: The objective here is to design the Front Fender of a car with Drip Area, Sill Mount area, Bumper mount region and A-pillar mount Region. Theory: Fender is the part of an automobile car that covers the wheel to prevent the sand, mud, rocks, liquids and other road spray from being thrown into the air…

Objective: To design outer panel of Hood with Hem and develop the Inner panel with all necessary reinforcements definition then positioning of Hinge, striker and create provision for mastic sealant points. Theory:The Hood or the Bonnet of a car is considered as the frontal BIW enclosure component. Bonnets are designed…

Objective: To calculate the Wheel Arc area of the given Fender and prove whether the car will pass the European standards regulations or not. Theory: While the design considerations of Fender we need to concentrate more on two critical areas in which first one is dripping area which is the area where the fender will be…

If the below slides are not clear, please Visit the below Link for the same Powerpoint file.https://drive.google.com/file/d/1tBhZCcOrPXwiQfxnn-vEiY9d-3WqezZa/view?usp=sharing                         Best Regards,Gowtham Kumar P.

Introduction of Underbody Coating:A Car Body is made up of several Metals such as Iron, Steel, Aluminum, Copper etc. Rusting is the common term for corrosion of iron and its alloys. Corrosion is the reaction of Iron and Oxygen, as may present in Water or Air Moisture. Any Iron material when exposed to both oxygen…

Objective:Design, Assembly and Photo realistic rendering of Sunseeker predator Yacht in Solidworks software. Steps Followed to create Yacht model and Assembly:First created the Blue prints setup by importing pictures of yacht using the sketch picture option in sketch tools and then modelled the parts of yacht which are…

Objective: To learn and understand the different tools available in Solidworks software through Design and Rendering of the American chopper project. The details of the tools used in the design of Chopper assembly are mentioned as below. Sketch Tools: such as 2d sketch and geometry creations using various geometry creation…