ASSIGNMENT-3

Week 4-1D Element Creation Challenge OBJECTIVE:  The Objective of this challenge is to create the mesh on the given component with the Size of 5 Units. To Create 1D elements on the following component with given cross-section and DOF. a. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX-…

Worm Gear Challenge OBJECTIVE: The main objective of this challenge is to perform a Transient structural Analysis on a worm gear assembly with finer mesh. To cut the gear by half so as to bring the model within limits, to rotate the worm so as to get to almost end of the half cut and to get results for Equivalent stress,…

Bullet penetrating a Bucket OBJECTIVE: The main objective of this challenge is to perform explicit dynamic analysis of a Bullet penetrating a Bucket and to simulate a bullet penetrating into a bucket by using 3 different non linear materials for the bucket and to analyse their behaviour for the same velocity of bullet.…

Car Crash simulation OBJECTIVE: The main objective of this challenge is to perform explicit dynamic analysis of a car body and to perform a parametric study using 3 different values of thickness such as 0.3mm, 0.5mm and 0.6mm for the car body. To apply the same conditions as mentioned in the video and to analyse the total…

Machining with Planer  OBJECTIVE: The main objective of this challenge is to perform an explicit dynamics simulation of machining with planer, and to find out the Equivalent Stress, Total Deformation and also to insert a User defined result to calculate the temperature of the body. We need to perform this…

Tension and Torsion test challenge OBJECTIVE: The main objective of this challenge is to perform the tension and torsion test on the specimen provided. Case-1 For the tension test, to displace one end of the specimen to 18mm while keeping the other fixed. Also to find out the total deformation, equivalent stress and temperature…

Universal Joint OBJECTIVE: The main objective of this challenge is to perform a Transient structural Analysis on a double universal joint with a spring using three different materials such as Structural Steel, Stainless Steel and Titanium alloy. And to obtain the Equivalent stress and total deformation for…

Wire Bending Challenge OBJECTIVE: The objective of this challenge is to perform a static structural analysis and to Simulate the bending of a wire in ANSYS. And we have to use Copper Alloy (Non Linear), Aluminium Alloy (Non Linear) and Magnesium Alloy ( Non Linear) for the wire alone. And we need to find out the Equivalent…

Long Piston With Cam OBJECTIVE: The main objective of this challenge is to perform a Transient structural Analysis on a piston and cam mechanism and to run the analysis with Frictionless contact, Frictional with 0.1 and 0.2 as the frictional contact for a total of 3 cases, as well as to find out the Equivalent…

Bending of iPhone OBJECTIVE:  The objective of this challenge is to perform a static structural analysis and to Simulate the bending of iPhone as per the given cases below and  to obtain the directional deformation for the model, Factor of Aluminium Alloy NL and Life of the Aluminium…

Sphere pressing on a plate OBJECTIVE: The objective of this challenge is to perform a static structural analysis and to simulate a sphere pressing on a plate by using Structural steel for both sphere and plate but the material of the plate must be Non Linear. And to Press the sphere onto plate 4mm downwards and retract…

Rolling operation OBJECTIVE:  The objective of this challenge is to perform a static structural analysis and to Simulate the rolling operation on a workpiece made of copper for 14 steps and to ensure that the edge of the workpiece is displaced by 90mm. Finally to find out the Equivalent stress…

Sheet metal Bending challenge OBJECTIVE: The main objective of this challenge is to perform a static structural Analysis on sheet metal bending for 3 Different materials mentioned below. And to run the analysis for the following material: Case 1:Aluminium Alloy 1199,Copper Alloy NL and Magnesium Alloy NL. To find out the…

Verification of Weld Joints OBJECTIVE: The objective of this challenge is to perform a static structural analysis and to Simulate three different types of welding by using three different weld materials such as Stainless Steel,  Aluminium Alloy and Bronze cast. And to run the simulation…

                                                                                     Railwheel and Track OBJECTIVE: The objective of this challenge is to perform a static structural analysis on the Railwheel and Track setup and to Compare the Total Deformation, Equivalent stress and the life under the two bearing loads…

                                                                                                                    Grid Dependency Test for the Bevel Gear Simulation  OBJECTIVE:                     The main objective of this challenge is to perform a Grid Dependency Test fot the Bevel Gear with different element sizes…

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                                                                                                  Assignment 6 OBJECTIVE:  The main objective of  this challenge, is to write a python programme to fit Linear, Quadratic  and Cubic polynomial for the Cp data.…

                                                                                ASSIGNMENT 4        …

                                                                                ASSIGNMENT 3        …

           1.MODELLING OF A SUNSEEKER PREDATOR YACHT     1.OBJECTIVE:                    The main objective of performing this modelling is to produce a detailed model of different parts of a SUNSEEKER PREDATOR YACHT, as well as assigning…

MODELLING, ASSEMBLING AND RENDERING OF AN AMERICAN CHOPPER INTRODUCTION: The SOLIDWORKS® CAD software is a mechanical design automation application that lets designers quickly sketch out ideas, experiment with features and dimensions, and produce models and detailed drawings. SOLIDWORKS uses a 3D design approach. As…

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

                                                                                           …

https://drive.google.com/open?id=1vP7xaZ_UNM63jiNRMoDggj_ucGVSBluV

https://drive.google.com/open?id=1g-XDSU4bMBdxIgyH95Zp7lnmv5LE1KO_

https://drive.google.com/open?id=1Hsok6zsg4Tcehl2YWMaCb8mvAmtJ2t_0

https://drive.google.com/open?id=1dZ_ChwBj4vX99gt4crjF8Aij-120am9i