Pendulam simulation on MATLAB

AHMED BODY SIMULATION CHALLENGE   # Ahmed body description and its importance. The Ahmed Body was first created by S.R. Ahmed in his research “Some Salient Features of the Time-Averaged Ground Vehicle Wake” in 1984. Ahmed body is the benchmark model for aerodynamics simulation tools.  The simple geometrical…

Objective:  The main objective of this project is to simulate flow over a cylinder using steady and transient mode and Study the the vortex shedding in both the mode To calculate Strouhal number for the steady and transient simulations. Von karman Vortex Shedding: In fluid dynamics, a Kármán vortex street…

Theory: The main objective of this challenge is to solve the 2-D heat conduction equation for steady and unsteady state using iterative techniques such as jacobi, gauss seidal, and successive over relaxation method. This heat equation is need to be solve by both explicit(where RHS terms are the terms of previous time steps)…

https://drive.google.com/drive/folders/1oyrNH2bQQYVDPl19lbcaHkhKf8FIos8O?usp=sharing The above link Contains part like Oil tank, Chain and Pedal of an American Chopper  

Problem statement: In this challenge , a furnace is used to burn the methane in the presence of Air. A recuperator is connected after the furnace to recover some energy.what is the effect of pre-heating on the AFT?? Pre-heating temperature is varied from 298k-600k. Does preheating help with fuel saving? If yes, how does…

  A simple pendulum consists of a mass m hanging from a string of length L and fixed at a pivot point P. When displaced to an initial angle and released, the pendulum will swing back and forth with periodic motion. By applying Newton\'s second law for rotational systems, the equation of motion…

https://drive.google.com/drive/folders/1m00o3cpDWRvo3l75uu6Yf6orAbRdA2Rx?usp=sharing The Above link contains Front fender , back fender and Transmission Belt of a American Chopper  

Objectives : To describe in brief some practical CFD models he mathematical analysis of Rayleigh Taylor waves and to explain how these mathematical models have been adapted for CFD calculations. To Perform Rayleigh Taylor instability simulation for mesh sizes of 0.5mm , 0.3mm, 0.2 mm and to compare the results by showing…

#Objective of this challenge: To compare the Cell count , Outlet temperature and the number iteration for convergence for different cases with different length of tee and different momemtum ratios. #Introdution to Mixing Tee: Mixing Tee is also called as the T-joint because it splits the flow and the angle between them…

Introduction: A cyclonic separation is a method of removing particulates from an air, gas or liquid stream, without the use of filters, through vortex separation. When removing particulate matter from liquid, a hydrocyclone is used; while from gas, a gas cyclone is used. Rotational effects and gravity are used to separate…

Code: \"\"\" program to vary the temperature of fuel and oxidizer individually \"\"\" import cantera as ct gas = ct.Solution(\'gri30.cti\') A=ct.Quantity(gas) A.TPX = 298.15, ct.one_atm,{\'O2\':0.21,\'N2\':0.79} A.moles = 2/0.21 A.mass_fraction_dict() B=ct.Quantity(gas) B.TPX = 298.15,ct.one_atm,\'CH4:1546\' B.moles =…

Reaction Mechanism 1.CO + `O_2` -> `CO_2` + O 2.O + `H_2O` -> OH + OH 3.CO + OH -> `CO_2` + H 4.H + `O_2` -> OH + O    i ------> Reaction number   j         Species                 1    …

Objective: To write a code to solve the 1D supersonic nozzle flow equations using the Macormack Method Compare the results obtained using conservative and non-conservative forms of the governing equations Perform grid dependence test   Problem Setup: Consider a steady , isentropic flow through a convergent -divergent…

A simple pendulum consists of a mass m hanging from a string of length L and fixed at a pivot point P. When displaced to an initial angle and released, the pendulum will swing back and forth with periodic motion. By applying Newton\'s second law for rotational systems, the equation of motion for the…

    When does a ODE become unstable? --->     The ODE becomes unstable when we increase the time step(for explicit method only) for example in the python code below , an ODE is solved explicitly and the results are also shown below \"\"\" Explicit euler demo \"\"\" import math import…

[Part 1/2] Objective of the project: 1.The main objective of this project is to simulate the laminar flow through pipe. The wedge portion is taken as the whole circular section (cylinder) may take time to simulate or it may be costly if your computer do not have much resources. 2. The other objectives is to write the Matlab…

[Part 2/2] Objective of the project: 1.The main objective of this project is to simulate the laminar flow through pipe. The wedge portion is taken as the whole circular section (cylinder) may take time to simulate or it may be costly if your computer do not have much resources. 2. The other objectives is to write the Matlab…

Give a brief description of why and where a CHT analysis is used. Conjugate heat transfer (CHT) refers to the coupling of conduction in solids with the convective and radiative heat transfer in the surrounding fluids. Accurately predicting CHT is an essential part of the design process. Conjugate heat transfer investigation…

Rankine cycle theory: The ideal Rankine cycle consists of the following four processes, as Shown in the results and the figure 1.1 1-2: Isentropic Expansion in the turbine 2-3: Constant Pressure heat Rejection in a Condensor 3-4: Isentropic Compression in a Compressor 4-1: Constant Pressure heat Addition in a Boiler  …

The main motive of this code is to read the thermodynamic data file to extract the polynomials of the various species and to calculate various properties such as specific heat , enthalpy and entropy.   The formulaes developed by the NASA are given below where a1,a2,a3,a4,a5,a6,a7 are the coefficients and T are the…