Drag Force for multiple velocity inputs and multiple drag coefficient inputs

Code for data analysis import matplotlib.pyplot as plt import math import numpy as np try: #Try-Except Syntax. If an error is found in TRY it runs the EXCEPT command file = open(\'engine_data.out\',\'r\') except: print(\' >>> File cannot be recognized. Please check again <<< \') value=[] for line in file:…

1: Popt gives the optimal values of the co-efficients present in the polynomial     Pcov gives the the estimated covariance of the corresponding popt   2: np.array(temperature) is used to convert the temperature into an array therefore able      to be multiplied with the coefficients…

Python program to display PV diagram of OTTO CYCLE/ Air Standard Cycle # Otto Cycle import matplotlib.pyplot as plt import math as m import numpy as np # Inputs gamma = 1.4 t3 = 2250 # State variables at Stage 1 p1 = 101325 t1 = 600 # Engine geometric parameters bore = 0.25 stroke = 0.25 con_rod = 0.2 cr = 12 def engine_kinematics(bore,stroke,con_rod,cr,start_crank,end_crank):…

Youtube link: https://youtu.be/b9Jhyk6Zqbw   # forward kinematics animation import matplotlib.pyplot as plt import math as m import numpy as np import os # Inputs l1 = 2 l2 = 1 x0 = 0 y0 = 0 theta1 = np.linspace(0,(m.pi/2),10) theta2 = np.linspace(0,(m.pi/2),10) count =1 os.makedirs(\'2r_robot_images\') os.chdir(\'C:/Users/Venki_LFC/Documents/Study/Python/2r_robot_images\')…

This program results in two graph outputs. 1.Drag force vs Velocity ( Co-efficient is constant, velocity varies) 2.Drag Force vs Drag Coefficient (Velocity is constant, Drag Coefficient varies) The Drag force vs Velocity Graph shows that for increasing velocity the force increases exponentially since velocity^2 is…

The following code is used to simulate the forward kinematics of a 2R Robotic arm. I used Gif online maker to animate. Youtube Link: https://youtu.be/NHFgr_p3Ims % forward kinematics clc close all clear all l1 = 2; l2 = 1; x0 = 0; y0 = 0; theta1 = linspace(0,90,10); theta2 = linspace(0,90,10); count =1; for i= 1:length(theta1)…

NASA FILE PARSING The following codes are used to parse the thermo30.dat file and extract the values used for calculating the entropt, enthalpy, specific heat and molecular weights of several compounds. Then they are plotted vs temperature. Main program clear all close all clc file = fopen(\'thermo30.dat\',\'r\'); head1…

Section 1 The genetic algorithm is a method (function in MATLAB) for solving both constrained and unconstrained optimization problems that is based on Charles Darwin\'s Theory of Natural Selection, which says the fittest among the group survives. GA generates a number of points at each iteration. The best point in the…

Code for Curve Fitting - Linear and Cubic clear all close all clc % Data Preparation cp_data = load(\'data_hw\'); temp = cp_data(:,1); cp = cp_data(:,2); % Curve fit co_eff_linear = polyfit(temp,cp,1); co_eff_cubic = polyfit(temp,cp,3); predicted_cp_linear = polyval(co_eff_linear,temp); predicted_cp_cubic = polyval(co_eff_cubic,temp);…

Simple Pendulum Problem Youtube Link: https://youtu.be/ADz-aGrM5Gk clear all close all clc b = 0.5; g = 9.81; l = 1; m = 1; % Initial Condition theta_0 = [0;3]; % Time points t_span = linspace(0,20,500); % Solve ODE [t,results] = ode45(@(t,theta) ode_func(t,theta,b,g,l,m),t_span,theta_0); figure(1) plot(t,results(:,1))…

OTTO CYCLE (PV and efficiency) clc close all clear all % Inputs gamma = 1.4; t3 = 2250; % State variables at Stage 1 p1 = 101325; t1 = 600; % Engine geometric parameters bore = 0.25; stroke = 0.25; con_rod = 0.2; cr = 12; % Swept volume and clearance volume v_swept = (pi/4)*bore^2*stroke; v_clear = v_swept/(cr-1); v1 =…

1. Code for Drag Force vs Velocity Graph (Drag coefficient being constant) % Calculation of Drag Force clear all close all clc % Inputs density = 1.35; % the value of density (kg/m^3) area = 5; % the value of frontal area (m^2) vel = [20:45]; % the value of velocity (m/s) cd = 0.5; % Constant drag coefficient % Drag Force…