1. AIM :- To analyse the multi body dynamics for Internal Geneva Mechanism using SolidWorks. 2.OBJECTIVES: To create 3D models for driver and driven wheels To perform motion analysis by rotating the driver wheel at 10rpm. To obtain the following plots: Contact force (between driving and the driven wheel) as a function…

AIM :   To simulate the transient behaviour of a simple pendulum and to create an animation of it's motion on MATLAB. OBJECTIVE : 1.To write a program that solves the second order ODE corresponding to motion of a simple pendulum and to plot its angular displacement and angular velocity wrt time 2.To…

1.AIM - Motion analysis on the planetary gear Assembly with a carrier and to perform  motion analysis for different configurations of the gearset and to compare the angular velocities. 2.OBJECTIVES : model the ring gear using toolbox in SolidWorks. model the sun gear using toolbox in SolidWorks model the…

1.AIM : To model the Valve Train components for IC Engine and assemble than to get the simulations in Solidworks According to the Following cases. 2.OBJECTIVE: - Our objective is to create a 3D model and Simulation on IC Engine Valve Train in solidwork  and plot the variation of linear displacement  with…

Aim:  The aim is to perform a MBD simulation on a Piston Assembly using Solidworks. Introduction & Basic Theory: Multi-Body Dynamics or MBD is the study of the movement of various parts in the assembly with each other. By performing MBD one can see the behaviour or path trached by the different parts present…

Aim: Optimization using genetic algorithm and to determine the global maximum function using MATLAB. Objectives: Clearly explaining the concept of genetic algorithm. Explaining  the syntax for ga in Matlab. Codes gives the same output, even if it is made to run several times. Plot graphs for all 3 studies…

Aim:        The aim of the project is to run an external flow baseline simulation over a cylinder and then calculating the Reynolds number for every 20, 40 and 100%. A transient simulation has to run and calculate the simulation end time. Objective: Design the cylinder in solidworks and run a flow simulation…

Aim:   To perform an external flow simulation on a NACA0017 airfoil and compare the drag and lift force for every angle of attack at 0,2,4,6,8,10 deg. OBJECTIVES To compare the lift force and drag force of an airfoil for different angle of attacks. THEORY The NACA airfoils are airfoils shapes of an aircraft wings…

Aim : To perform a flow bench simulation for different mesh grid size to select the best grid and check the velocity and pressure plots for every valve opening from minimum opening to maximum opening for mass flow rate. OBJECTIVE:• To perform a Grid dependence test.• Simulating three grids at a particular valve…

AIM : To find out the critical frequencies of a rotating shaft in Solidworks. OBJECTIVES : To create 3D model of a rotating shaft. To perform frequency analysis on the rotating shaft and find out the critical frequencies. INTRODUCTION : Frequency is the number of occurrences of a repeating event…

AIM:              To write a code in Matlab/Octave to parse the NASA thermodynamic data file and then calculate thermodynamic properties of various gas species. OBJECTIVE:    Write a function that extracts the 14 co-efficients and calculates the enthalpy, entropy and specific…

AIM : To create a Rankine Cycle Simulator using MATLAB. OBJECTIVE : To calculate the state points of the Rankine Cycle based on user inputs.  To plot the corresponding T-s and h-s plots for the given set of inputs. THEORY : The Rankine cycle is the fundamental operating cycle of all power plants…

AIM: To create a centrifugal pump geometry to perform the flow simulation using Solidworks and obtaining the analysis results to view the relationship between the mass flow rate and pressure ratio. OBJECTIVE To Create a 3D Model of Centrifugal Pump and to run a Flow Simulation. To Obtain a relation between Pressure ratio…

AIM :- To write code that can solve an otto cycle and make plots for it. OBJECTIVES :-  1. Write a code to plot a PV diagram. 2. Find the thermal efficiency of the engine. THEORY :- The Otto cycle is the ideal cycle for spark-ignition engines, in honor of Nikolaus Otto, who invented it in 1867.  An Otto…

Aim – Solving a second order Ordinary Differential Equation (ODE) using Python Objective – To write a program which can solve a second order Ordinary Differential Equation (ODE). To plot the displacement and velocity graph for a simple pendulum. To create an animation for a simple pendulum motion.   Problem…

AIM: To write a code to perform curve fitting in Python. OBJECTIVES: Write code to fit a linear and cubic polynomial for the Cp data provided. Plot the linear and cubic fit curves along with the raw data points. Explain the parameters used to measure the fitness characteristics for both the curves. Theory - …

Aim: Performing data Analysis on Engine Performance Data using PYTHON. Objective -  There are four objectives :-  To perform data analysis and a) plot a graph between any two quantities (like pressure vs volume, pressure vs crank, crank vs volume, etc.)  b) calculate the area under P-V diagram c) calculate…