You will be introduced to the concept of FEA, and the fundamentals of the stress-strain graph. You will be taught the various types of FEA analysis, and the different processes in performing an analysis. You will also learn about linear and non-linear simulations. 

• You will be introduced to different types of FEA analysis
• You will understand the types and effects FEA analysis will have on the same model

In this module, you will learn how to perform a 1D/2D/3D analysis on a cantilever beam. You will design the model and understand how to do the static analysis. You will be taught how to perform a design study. Finally, you will learn how to compare the results in the SOLIDWORKS. 

• You will learn how to perform analysis on a cantilever beam
• You will learn the different conditions and settings to replicate the model within the software 
• You will perform 1D,2D, and 3D analyses on the same model and you will compare the results
• You will then run the simulation through a post-processor to return the results

You will be trained in how to import a neutral file and clean up the geometry for the structural analysis following which you will be introduced to the concept of buckling analysis. 

• You will be Introduced to buckling analysis in SOLIDWORKS
• You will understand how to increase the factor of safety of the model

In this module, you will learn about the fatigue analysis and the effect of the S-N curve. You will learn the types of loading available for the fatigue analysis. You will learn how to import the results of the static analysis to the fatigue analysis and how to create an animation from the results. 

• You will be introduced to fatigue analysis in SOLIDWORKS
• You will understand the speed and torque variation

In this module, you will learn about the requirements for doing a drop test in a PCB board and plot the results. 

• You will learn how to perform a drop test on a model
• You will understand the various factors that affect the drop test
• You will post-process the simulation and identify the results

In this module, you will learn the concepts of the vibration and the modes of vibration. You will learn about the types of solvers available in SOLIDWORKS for the frequency analysis and how to perform the frequency analysis in SOLIDWORKS.

• You will have a brief introduction to frequency analysis in SOLIDWORKS
• You will figure out the different mode shapes of a rectangular beam using frequency analysis
• You will learn how to perform frequency analysis using a PCB 

You will be introduced to motion study in SOLIDWORKS. You will learn the concepts of the Geneva mechanism and their types. You will also learn how to model and assemble the external Geneva mechanism, and how to perform a motion study on it. You will learn how to plot the contact force between the parts. 

In this module, you will study the following, 

• Understanding the basics of modelling and assembling in SOLIDWORKS
• Pre-processing the model for the motion analysis and running a simulation
• Post-processing the simulation to get the results as plots

You will be introduced to the machine vice and will learn to model and assemble the machine vice. You will learn about screw mates and how to perform motion studies on it. 

These are the things you will learn in this module, 

• Introduction to the screw mate
• Tracing the displacement of the movable jaw

You will learn the concepts of the planetary gear train and gear terminology. You will learn how to import the standards gears in SOLIDWORKS to do the motion study. 

These are the topics that be covered in this module, 

• Learning the basic gear terminology to model a gear
• Understanding the speed and torque variation
• Learning about the application of gear mate

You will learn about the concepts of the IC engine piston kinematics and you will learn how to design and do the motion study. 

You will study the following in this module, 

• Understanding the effect of wrist pin offset in the piston displacement.
• Assigning the material to the parts

You will learn to model the IC engine valve train. You will learn the effect of spring in the valve train. You will learn how to calculate the cam lift and will design the cam based on it. 

These are the topics you will study in this module, 

• Understanding the application of the CAM
• Performing a calculation to model the CAM as per the valve lift specifications.
• Studying about the damping coefficient and the free length of spring

You will learn to model simple geometry using SOLIDWORKS. You will also learn how to set up a fluid study in SOLIDWORKS, and understand necessary boundary conditions, along with the initial conditions to run the simulation. In this module, you will learn how to change the mesh settings as well. 

You will be trained in the following. 

• Simulating flow through a pipe is a classical CFD problem. It offers insight into the various inputs that go into running a CFD simulation.
• Introduction to parametric studies and grid dependency test.
• Understand the concepts of global maxima and global minima. 

• Simulate the flow over a 2D NACA airfoil
• Calculate the drag and lift forces for the various angles of attacks.

• Perform transient analysis at different valve lifts
• Create a plot of lift vs mass flow rate

In this module, you will be introduced to the concept of moving reference frame while also learning about the rotating body feature in SOLIDWORKS.

You will perform the following projects within this module, 

• Using the MRF approach to simulate flow through a Centrifugal pump
• Plotting a pump performance curve

You will be introduced to MATLAB and you will be taught the basics of MATLAB by using a top-down approach. That is, you will start directly by solving problems and stop in the required places to learn about the fundamentals of programming.

• You will learn the MATLAB syntax and the various commands used in it.
• You will understand the methods and the ways to use the commands in different scenarios.
• You will learn to manipulate your own calculations and comparisons
• You will learn about the use of arrays.
• You will learn about the Functions used along with plotting, creating movies, creating figures etc

• You will animate the manipulator motion using ImageMagick.
• Here you will learn about the simulation part
• And you will learn how to create a movie clip along with the spatial motions of Robotic arm
• You will learn how the FOR loop plays a role in the programming
• And how the “hold on” command works
• And about the arrays and linspace commands

In this module, you will write code to simulate an Air Standard Cycle.

• Your code will solve the piston kinematics equation to calculate the volume trace.
• Your code will create PV diagrams for different operating conditions.
• You will learn how to work on various thermodynamic relationships
• You will learn about the pressure-volume variations.
• And you will learn how the order of the program is significant
• Functions can be cleared through this challenge
• You will also learn about the plots, legends used in the graphs
• Finally, you will learn about the piston kinematics

• Implement BDF and FDF methods to solve ODEs
• Learn about the real use of differential equations
• How the differential equations connect to the real-world applications and how to solve those differential equations
• You will learn about the ODE solvers, and also about the syntax of ODE’s, and also about various supplementary commands

• An engineer needs to understand the dependence between system input and output. Curve-fits are a great tool to do this. In this module, you will learn how to perform curve fits with MATLAB.
• Curve fits and regression are the part of Machine learning and Neural Networks
• Curve fitting helps you to make a comparison study with the original ideal data set with the experimental one 
• And you will learn about the polynomials and their best fits
• You will learn about the PolyFit and PolyVal commands
• You will know how to calculate the errors
• You will learn about SSR, SSE, SST

• Genetic Algorithm is a procedure to optimize multi-parameter systems. It is used to optimize different types of systems and processes.
• You will learn about the optimization techniques used in industries
• Genetic Algorithm is one of the optimization techniques used widely and you will learn how GA works
• You can easily optimize their values using the Genetic Algorithm
• You will know about the GA syntax and how to get the global maxima 
• You will also learn about the options, they can include apart from the default one and also about the stalagmite functions and how it works.
• And also about the population size, number of generations, fitness value, and termination of further generations